Skip to main content

Getting started with beekeeping: how to harvest honey

While honey is not the only product from a beehive, its the one that most beekeepers are interested in and it usually takes a year or so to let the bees build up numbers and store enough honey before there is enough to harvest.  There are a few different ways to extract honey from frames.  We have a manual turn 2-frame certifugal extractor.  A lot of people with only a few hives will just crush and strain the comb.  This post is about how we've been extracting honey so far (four times now), and there are links at the end to other bloggers who use different methods so you can compare.



Choose your frames
Effectively the honey is emergency food stores for the bees, so you have to be very careful not to take too much from the hive.  You need to be aware of what is flowering and going to flower next and the climate.  Particularly in areas with cold winters, where the bees cannot forage for some time.  We are lucky to have something flowering most of the year and can take honey in Spring and Summer.  You can take any frame that has more than 70% of the comb capped (sealed),  Don't worry if there is some brood on the comb - you will strain that out, but make sure you don't take the queen!  We stopped using queen excluders (that stop the queen getting into the top box) as it seemed to make the hive weaker.



Collect your frames
We put the frames that we are taking into a clean empty super, with a spare lid underneath, and put an escape board on top.  You can brush most of the bees off the frames, and then the rest will fly out of the escape board (it lets them out but not in again) and this means that MOST of the bees won't be joining you when you're extracting the honey.



Uncap the frames
We use a hot electric knife to uncap, you can also get steam knifes or use a scraping tool.  I have the scraping tool for doing little areas that the knife misses.  Pete operates the knife and aims to get MOST of the uncapping beeswax and honey into the bucket.  We got this neat little plastic board that fits over the bucket and holds the frame, really helpful!



Load up the extractor
We can it two frames in the extractor.  It works best if the load is balanced, so make sure you have the frames loaded opposite ways.  Sally wrote a great post for me before we ever extracted honey and I think of her wise words as I spin the extractor:
Spin the first side at half speed and only for a few turns to release half the honey in that side. Then stop, remove each frame, turn it around to its other side and replace into the extractor so the honey is being spun from the other side of the wax. Then spin the honey out gradually gathering more speed. Then turn the frames back to the first side again to remove the remaining honey in that side. This is to prevent breaking the wax as the weight of the honey and the centrifugal action forcing the frame to the outside is too heavy for the wax to remain in one piece. The least breakages in the wax means the bees can spend less time repairing the wax and spend more time gathering nectar and pollen to make honey.


Strain the honey
We got some nice stainless steel sieves for straining the honey into the first bucket, its easy to keep them clean.





Bottle and label your honey
I got new jars for our honey, I think that's nicer for customers, but we re-use plenty of other glass jars for our own use and to give to friends.  Research the labeling requirements in your state, we have to include the word "honey", the date of processing, our address and the country of origin.  More info here.


Clean up the sticky mess
Hot water is required to clean up all the sticky honey before the ants find you!  When the honey in the extractor is strained I then strain the cappings honey and melt down the remaining beeswax.

That's basically all there is to it.  Have you extracted honey?  What method do you use?

Here's some inspiration from other bloggers:





Schneiderpeeps - bees (an update)  - with photos from a crush and strain experiment






Comments

  1. Hi Liz, So nice to see the honey flowing. We have lost the last of our 3 hives. We know they had lots of stores but we think that the final unexpected freeze mid February did them in. I don't think we had the numbers needed for the winter cluster.
    We will pack everything away and leave one hive out in the hope we may receive a swarm as we will be out-of-country till the beginning of August.
    All the best. Hope your winter gives you relieve from the high temperatures you have experienced this past summer.
    Regards Janine

    ReplyDelete
  2. Liz I can't remember how my husband used to extract the honey as he didn't have a lot of equipment. I found a bottle of honey pushed to the back of the cupboard a while back and it was many, many years old from when he used to keep bees. It was still good of course. Several of our Simple Living Toowoomba members have joined the local bee keeping group after we had a bee keeping workshop last year.

    ReplyDelete
  3. Nice post. I took up beekeeping last year and I am having a blast! Your readers might be interested in this online course (it's free): https://www.perfectbee.com/course/

    ReplyDelete

Post a Comment

Thanks, I appreciate all your comments, suggestions and questions, but I don't always get time to reply right away. If you need me to reply personally to a question, please leave your email address in the comment or in your profile, or email me directly on eight.acres.liz at gmail.com

Popular posts from this blog

The new Eight Acres website is live!

Very soon this blogspot address will automatically redirect to the new Eight Acres site, but in the meantime, you can check it out here .  You will find all my soaps, ebooks and beeswax/honey products there, as well as the blog (needs a tidy up, but its all there!).  I will be gradually updating all my social media links and updating and sharing blog posts over the next few months.  I'm very excited to share this new website with you!

Chicken tractor guest post

Sign up for my weekly email updates here , you will find out more about chickens, soap and our farmlife, straight to your inbox, never miss a post!  New soap website and shop opening soon.... Tanya from Lovely Greens invited me to write a guest post on chicken tractors for her blog.  I can't believe how many page views I get for chicken tractors, they seem to be a real area of interest and I hope that the information on my blog has helped people.  I find that when I use something everyday, I forget the details that other people may not be aware of, so in this post for Tanya, I tried to just write everything I could think of that I haven't covered in previous posts.  I tried to explain everything we do and why, so that people in other locations and situations can figure out how best to use chicken tractors with their own chickens. The dogs like to hang out behind the chicken tractors and eat chicken poo.  Dogs are gross! If you want to read more about chicken tractor

How to make soap with beer (and tallow)

I may  have mentioned this before.... soap making is addictive!  Once you start, you just want to keep making more soap.  And not the same soap, you want to try all sorts of different soaps.  I made the mistake of joining a facebook group called Saponification Nation  and now my facebook newsfeed is full of glorious soaps, in all colours and shapes, which makes it even harder to resist the urge to experiment.  One soap that kept popping up a few weeks ago was soap made with beer. I generally prefer not to use ingredients just for the sake of it, I like to know that they are adding something to the properties of the finished soap.   As you know, I don't like to use artificial ingredients either (colours or fragrances).   When I read about beer in soap I found out that beer adds sugar to the mixture, which increases lather.  I use tallow in my soap, which has limited lather, so anything that adds lather could improve the soap.  It also contributes a tan or brown colour to