Skip to main content

Winter Woodfires: installing a woodfire

Installing a woodfire is a complicated process!  Of course we decided to do it ourselves, why pay an expert when you can figure it out yourself?  I've already explained why we love our woodfire, so this is more detail of the installation process.

The hardest part is the weight of the woodfire.  They are made of cast iron and range from 100-300 kg.  This is not easy to move!  The first woodfire we bought (a Nectre Baker's oven) was only 120 kg, which was lucky because it had to get into the top floor of our Queenslander!  My husband borrowed a three-wheeled stair climbing trolley and he and a friend pushed and pulled the oven up our front stairs (while I watched, holding my breath, worried that the stairs would collapse).  The second stove (a Scandia Cuisine) was 248 kg!  Luckily this one only had to come into a low-set house.  My husband backed the ute up to the verandah and we wheeled the oven off the ute and onto the verandah using a set of ramps and a SCA trolley (I was still holding my breath though!).

The next challenge was making a hearth.  In the first house we were replacing an existing stove, so we just popped the oven down on the old hearth.  The second house had no stove, so we had to build a hearth ourselves.  Fortunately we had found some of the spare floor tiles under the house.  There was just enough to build a hearth to go under and behind the oven (even with tiled floors, you still need a raised hearth to protect the floor).  This meant that my husband had to build a frame from box section, to which he screwed fibro-cement board and then glued the tiles.  This was our first go at tiling anything and its not as easy as it looks!  My only advice is don't be stingy with the cement, or you will get cracked tiles, especially when you're putting 200 kg of oven on top (another one learnt the hard way!).  Anyway, we got a suitable hearth built (note that you CAN buy these, but we chose to make life hard for ourselves and tried to match the hearth to the floor tiles) and positioned the stove.

The next step was installing the flue.  In the first house, it was easy as there was already a hole in the ceiling and roof from the old stove, so my husband just had to modify that and put it all together with the help of a friend.  Again, you can pay someone to install the flue, but we thought we'd have a go ourselves!  In our current house, we had to start from scratch, so first my husband worked out where the beams in the roof were and cut a hole in the ceiling, and then the roof (after lifting the tin), then we pushed the inner flue through the ceiling.  Then I had to join my husband on the roof and help with the outer flue (scary!) and position the top hat.  We screwed and riveted it together and put heaps of silicon around the "deck tight".  In the end we had a water tight flue, so we thought it was a great success.....

The first flue was easy to fit as there was already a hole
(and I didn't have to help!)

The second flue was fitted from scratch,
but I think we did a nice job.

The flue on the inside of the house
Last winter we always had a bit of trouble with the stove.  We found it difficult to start, the draft just wouldn't get established and the smoke would come out into the room.  We thought it was a problem with the oven, so we contacted Scandia to ask their advice.  They had two suggestions:
  • The flue may be blocked, so thoroughly clean the stove and flue
  • Extend the flue, it should be 3.2 m long and ours was only about 2.8 m due to the flue kit we purchased and trimming to get the inside and outside to be the same length.  (more info on backdrafting here)
  • Use better wood (more about this here)
My husband was keen to fix the problem and started to clean the stove straight away.  Copious amounts of creosote had apparently fallen down from the flue and were stuck in the internals of the stove, this was not a good sign (plus a major fire hazard).  We decided to buy an extra section of flue (0.8 m).  It was not a simple task to add this section to the flue as the new section did not fit exactly into the old sections!  Its lucky that my husband can weld, or this would have been a disaster.  He ended up carefully welding the new section to one of the old sections.  This left us with one section of 1.6 m to put on the very top of the flue, which involved standing on things on the roof that we are definitely not allowed to do at work due to health and safety legislation!  Anyway, we now have a ridiculously long flue coming from our tiny house.

We had to extend the flue to improve the combustion performance.
Fortunately it was all worth the effort as we noticed the difference as soon as we lit the fire.  The draft was established immediately.  We had no trouble with smoke coming into the room at all.  The fire roared!  When we diverted the flue gas over the oven section, the oven heated up perfectly.  We should be doing more cooking on it this year :)  Bring on the roast potatoes!  I was amazed that 0.8m could make such a difference.

For more information about woodstoves see cooking on a woodstove, preparing firewood, and lighting the fire.
Have you ever installed a woodstove?

Comments

  1. Hi. I also love my woodstove! We've had a Nectre Bakers Oven for three winters now. Installed ourselves but purchased a prefab slate and timber hearth. We've had a small leak from the holes we had to cut through the ceiling and then the roof (we have a loft space between), which my husband is a bit confounded by. Such a shame as its caused some rust. We are only heating a 9x5m footprint house (half that space again in the 2nd story loft) so have no trouble keeping warm. In fact, often too warm! We've found the quality of the wood makes all the difference - last winter i couldn't get the fire to burn through till morning even after clearing flue etc, whereas first and third winter it's no problem at all. Our parents had same wood and mentioned same problem. I've just discovered your blog and will be back for sure. Seems we have some common goals. Cheers! Chantal

    ReplyDelete
  2. My tiny house is 12x14ft, however it is 14ft tall (4.26m). To capture as much heat as possible, we ran 3m worth of pipe straight up out of the firebox before it juts out the wall and above the roof. Works great for drafting and keeping smoke out!

    ReplyDelete
  3. I would like to install a fireplace in our house, though like you we'd have to do it from scratch. Thanks for sharing your tale, though I'll have to make sure my husband doesn't read this and realise that it might not be as easy as I keep telling him it will be...
    Christine

    ReplyDelete

Post a Comment

Thanks, I appreciate all your comments, suggestions and questions, but I don't always get time to reply right away. If you need me to reply personally to a question, please leave your email address in the comment or in your profile, or email me directly on eight.acres.liz at gmail.com

Popular posts from this blog

The new Eight Acres website is live!

Very soon this blogspot address will automatically redirect to the new Eight Acres site, but in the meantime, you can check it out here .  You will find all my soaps, ebooks and beeswax/honey products there, as well as the blog (needs a tidy up, but its all there!).  I will be gradually updating all my social media links and updating and sharing blog posts over the next few months.  I'm very excited to share this new website with you!

Chicken tractor guest post

Sign up for my weekly email updates here , you will find out more about chickens, soap and our farmlife, straight to your inbox, never miss a post!  New soap website and shop opening soon.... Tanya from Lovely Greens invited me to write a guest post on chicken tractors for her blog.  I can't believe how many page views I get for chicken tractors, they seem to be a real area of interest and I hope that the information on my blog has helped people.  I find that when I use something everyday, I forget the details that other people may not be aware of, so in this post for Tanya, I tried to just write everything I could think of that I haven't covered in previous posts.  I tried to explain everything we do and why, so that people in other locations and situations can figure out how best to use chicken tractors with their own chickens. The dogs like to hang out behind the chicken tractors and eat chicken poo.  Dogs are gross! If you want to read more about chicken tractor

How to make soap with beer (and tallow)

I may  have mentioned this before.... soap making is addictive!  Once you start, you just want to keep making more soap.  And not the same soap, you want to try all sorts of different soaps.  I made the mistake of joining a facebook group called Saponification Nation  and now my facebook newsfeed is full of glorious soaps, in all colours and shapes, which makes it even harder to resist the urge to experiment.  One soap that kept popping up a few weeks ago was soap made with beer. I generally prefer not to use ingredients just for the sake of it, I like to know that they are adding something to the properties of the finished soap.   As you know, I don't like to use artificial ingredients either (colours or fragrances).   When I read about beer in soap I found out that beer adds sugar to the mixture, which increases lather.  I use tallow in my soap, which has limited lather, so anything that adds lather could improve the soap.  It also contributes a tan or brown colour to